ECMA Series Motors - Delta Electronics, 400W - 15KW
Our ECMA Series Servo Motors are general purpose, permanent magnet servo motors. The ECMA series is plug-n-play with our A2 Intelligent or B2 Economy servo drives. This series of Servo motor is available from 50W to 15kW. The ECMA servo motor series is a state of the art Servo motor. Its segmented stator results in low flux loss. The case and bearings are designed to withstand 2.5Gs of vibration. Rare earth magnets, Neodymium-Iron-Boron (NeFeB) are used in the rotor for high torque to size ratio. Delta’s ECMA motor series is 10 pole design (unlike the more common 6 or 8 pole) and delivers low cogging and smoother motion than other servomotors on the market.
| Part # | Rating | RPM | Description |
| B3 Servo Motors (17-bit, IP67) | |||
| ECM-B3M-CM0604RJ1 | 400W | 3000 | 1.27Nm, PCD: 70, Flange: 60×60, Shaft: 14 |
| ECM-B3M-CM0807RJ1 | 750W | 3000 | 2.40Nm, PCD: 90, Flange: 80×80, Shaft: 19 |
| ECM-B3M-E21310RS1 | 1.0KW | 2000 | 4.77Nm, PCD: 115, Flange: 130×6130, Shaft: 22 |
| ECM-B3M-E21315RS1 | 1.5KW | 2000 | 7.16Nm, PCD: 145, Flange: 130×6130, Shaft: 22 |
| With built-in (24VDC) Brake | |||
| ECM-B3M-CM0604SJ1 | 400W | 3000 | 1.27Nm, PCD: 70, Flange: 60×60, Shaft: 14 |
| ECM-B3M-CM0807SJ1 | 700W | 3000 | 2.40Nm, PCD: 90, Flange: 80×80, Shaft: 19 |
| A2 Servo Motors – 20 Bit (With built-in (24VDC) Brake) | |||
| ECMA-C10807SS | 750W | 3000 | 2.36Nm, PCD: 90, Flange: 80×80, Shaft: 19 |
| ECMA-C11010SS | 1.0KW | 3000 | 3.18Nm, PCD: 115, Flange: 100×100, Shaft: 22 |
| ECMA-E11315SS | 1.5KW | 2000 | 7.16Nm, PCD: 145, Flange: 130×130, Shaft: 22 |
| ECMA-K11320SS | 2.0KW | 2000 | 9.55Nm, PCD: 145, Flange: 130×130, Shaft: 22 |
| ECMA-L11830SS | 3.0KW | 1500 | 19.10Nm, PCD: 200, Flange: 180×180, Shaft: 35 |
| ECMA-L11845SS | 4.5KW | 1500 | 28.65Nm, PCD: 200, Flange: 180×180, Shaft: 35 |
| A2 Servo Motors – 20 Bit (Without built-in (24VDC) Brake) | |||
| ECMA-C10604RS | 400W | 3000 | 1.27Nm, PCD: 70, Flange: 60×60, Shaft: 14 |
| ECMA-C10807RS | 750W | 3000 | 2.39Nm, PCD: 90, Flange: 80×80, Shaft: 19 |
| ECMA-C11010RS | 1.0KW | 3000 | 3.18Nm, PCD: 115, Flange: 100×100, Shaft: 22 |
| ECMA-E11315RS | 1.5KW | 2000 | 7.16Nm, PCD: 145, Flange: 130×130, Shaft: 22 |
| ECMA-K11320RS | 2.0KW | 2000 | 9.55Nm, PCD: 145, Flange: 130×130, Shaft: 22 |
| ECMA-L11830RS | 3.0KW | 1500 | 19.10Nm, PCD: 200, Flange: 180×180, Shaft: 35 |
| ECMA-L11845RS | 4.5KW | 1500 | 28.65Nm, PCD: 200, Flange: 180×180, Shaft: 35 |
| ECMA-L11855RS | 5.5KW | 1500 | 35Nm, PCD: 200, Flange: 180×180, Shaft: 42 |
| ECMA-L11875RS | 7.5KW | 1500 | 47.74Nm, PCD: 200, Flange: 180×180, Shaft: 42 |
| ECMA-L1221BR3 | 11.0KW | 1500 | 70Nm, PCD: 235, Flange: 220×220, Shaft: 42 |
| ECMA-L1221FRS | 15.0KW | 1500 | 95.40Nm, PCD: 235, Flange: 220×220, Shaft: 55 |